Back

2017 Exmark Lazer Z S-Series LZS749AKC604A1

MoreLess
Limited Time Offer!

Selling Price -$9,995.00
No Images Available

Selling Price -

$9,995.00

HD Certified Pre-Owned

2017 Exmark Lazer Z S-Series LZS749AKC604A1

More power. More features. More productivity.

With the S-Series, including an eco-friendly, Electronic Fuel Injection (EFI), Four UltraCut™ Series 4 cutting deck sizes are available with widths up to 72 inches. Want tough, try a 10-guage, formed and continuously seam-welded top and a 7-guage side skits. All with welded spindle mounting sites and full-floating 4-point suspension with four adjustable anti-scalp rollers.

Features may include:Our EFI system optimizes fuel delivery in real-time, which improves efficiency and performance. Gas-powered S-Series models have a single 12-gallon tank with one fill location.

  • Built to Last

Want tough? Try a 10-gauge, formed and continuously seam-welded top, and a 7-gauge side skirt. All with welded spindle mounting sites. And, full-floating, 4-point suspension with four adjustable anti-scalp rollers.

  • On-Board Diagnostics

Check vital functions at a glance on the digital screen. An electronic fuel gauge with low fuel warning on all Lazer Z units, battery voltage warning, hour meter and OPC safety switch monitoring make troubleshooting easy.

  • Fewer Grease Points

With just four grease points that only need annual greasing, the Lazer Z delivers maximum performance with minimum maintenance. Greaseless spindles and only four grease points on the entire machine.

  • Ultracut Series 4 Deck

This full-floating deck uses maintenance free spindle with a splined blade driver to stop bolt tightening on impacts. And, our patented bearing design on idler arm pivots only needs annual service.

  • Tool-less Belt Removal

Deck and hydro belt can be installed without using any tools.

  • 2017
  • Exmark
  • Lazer Z S-Series
  • LZS749AKC604A1
  • Riding
  • ECV749
  • Kohler® | Command™ EFI
  • Electronic Fuel Injected
  • 3,750 rpm | Infinitely variable speed selection from 0–10.0 mph (16 kmph) forward, 0–6.0 mph (9.7 kmph) reverse.
  • 747 cc.
  • Heavy-duty canister air filtration system
  • Gas EFI | Fuel Indicator: electronic Sender
  • 83.1 in. (211.1 cm)
  • 72.8 in. (184.9 cm) | Cutting Deck: 60"
  • 70 in. (177.8 cm) | Cutting: 1.0" (2.5 cm) to 5.5" (11.8 cm) in 0.25" (0.64 cm) increments adjustable from operator’s seat.
  • Deck: 10-gauge top that is formed and continuously seam welded, 7-gauge side skirt and 7-gauge formed and welded spindle mounting locations for improved strength and reduced weight. | Full-floating UltraCut Series 4. Side discharge standard, with molded discharge chute and option to bag or mulch.
  • 3 Blades at 20.50" Length | Spindles: No maintenance, sealed and non-greasable spindles; 7.75"-diameter cutter housing with 30mm (1.18")diameter spindle shaft and splined blade driver.
  • Blade Tip Speed: Approximately 18,500 fpm.
  • MagStop electromagnetic 200-ft-lb clutch with spot brake
  • 12-volt battery with 20-amp alternator.
  • Lever-actuated disc brake.
  • Hydro-Drive | Two Exmark exclusive Parker unitized pump and wheel motor systems with no hoses, integrated cooling fans, shock valve, 1.7-quart integrated reservoir, spin-on filter and heavy-duty components. 12 cc pumps and 14. 5 cubic inch motors.
  • Allows unit movement without engine running.
  • Control: Hydraulically dampened twin levers, adjust fore and aft. Adjustable dampeners (3 positions) to customize drive responsiveness. Also adjustable to 2 height positions.
  • Deck Lift: Standard; foot-controlled deck lift changes cutting height and lifts the deck to maneuver around obstacles, or place in transport position.
  • Unibody, welded, heavy-duty 1.5" x 3" tubular steel.
  • 12-gallon (45.4-L), single fuel tank with single fill location.
  • 24 x 12-12, Turf Master®
  • 24 x 12-12, Turf Master®
  • .50" thick caster yoke arms. | Front Caster Tires: 13 x 6.5-6, smooth-tread, semi-pneumatic.
  • 1249 lbs.
  • Carb Compliant | Cup Holder | 2-post foldable ROPS standard with seat belt and latch.
  • Operator Presence Controls (OPC) and drive system interlock, with safety interlock system indicators.
  • Deluxe, two-tone, bolstered suspension seat with Elastomeric Vibration Control material. Mounted on innovative Seat Isolation System that provides operator isolation in all three planes of motion as well as fore-aft slide and seat flip-up.
  • 7287
  • 60
  • Fabricated
  • KOHLER
  •  Calculation is estimate only.
  •  
  •  
  •  
  •  
  •  
  •  
  •  Quotes are estimates only, actual rate may vary slightly.
  •  One-Way toll road charges will be the responsibility of the customer.
  •  Additional fees and/or duties may apply to International and non-continental US shipping requests.
  • $9,995.00
  • Stryker, Ohio
  • Pre-Owned
  • LZS749AKC604-7287
  • 2017
  • Exmark
  • Lazer Z S-Series LZS749AKC604A1
  • KOHLER EFI
  • 392.5
  • Gas
  • Available
  • 72.8 in. (184.9 cm) | Cutting Deck: 60"
  • 70 in. (177.8 cm) | Cutting: 1.0" (2.5 cm) to 5.5" (11.8 cm) in 0.25" (0.64 cm) increments adjustable from operator’s seat.
  • 7287
  • 60
  • Fabricated
  • KOHLER

Recommendations

Advertised pricing excludes applicable taxes title and licensing, dealer set up, destination, reconditioning and are subject to change without notice. Pricing may exclude any added parts, accessories or installation unless otherwise noted. Sale prices include all applicable offers. Not all options listed available on pre-owned models. Contact dealer for details.